- Recent
- Popular
- Answered
- Unanswered
0helpful
1answer
Before deleting the current program and reprogramming your NX-8 wireless smoke detector, you may want to try the following troubleshooting steps:
- Check the batteries: Ensure that the batteries in your wireless smoke detector are not dead or low. Replace the batteries if necessary.
- Check the signal strength: Make sure that the wireless smoke detector is within range of the NX-8 control panel. You can try moving the detector closer to the panel to see if it helps.
- Check for interference: Interference from other wireless devices, metal objects, or thick walls can affect the signal strength. Try removing any potential sources of interference or relocating the detector.
If these steps do not resolve the issue, then deleting the current program and reprogramming the wireless smoke detector may be the next step. Be sure to follow the instructions in the NX-8 programming guide to properly delete and reprogram the detector. If you are not comfortable with programming the system yourself, you may want to contact a professional alarm company or technician for assistance.
Read full answer
2/25/2023 6:37:34 PM •Home•Answeredon Feb 25, 2023
0helpful
1answer
Unfortunately, without being able to see the spindle, it is difficult to provide specific instructions on how to remove it. However, in general, you should be able to remove the spindle by unscrewing it from the housing. You may need to use a pair of pliers or a wrench to get a better grip on the spindle. Once you have loosened the spindle, you should be able to pull it out of the housing.
Read full answer
2/22/2023 9:39:37 PM •Home•Answeredon Feb 22, 2023
0helpful
1answer
You can purchase the long black screw assembly from the manufacturer of the Fashion Bed Group Bunk Bed. You can contact them directly to inquire about purchasing the part.
Read full answer
2/22/2023 9:37:58 PM •Home•Answeredon Feb 22, 2023
0helpful
1answer
If the chime on your Daniel Dakota Grandfather clock has stopped working, it is likely due to a mechanical issue. You may need to take the clock to a professional clock repair shop to have it serviced. The repair shop should be able to diagnose the issue and make any necessary repairs.
Read full answer
2/22/2023 9:36:27 PM •Home•Answeredon Feb 22, 2023
0helpful
3answers
The medicines should be taken in the right amount and at the right time. Due to memory problems the seniors are not able to take in a right way, so a medication dispenser for seniors can be a good solution for that. A pill dispenser contains all the medication details along with scheduled time details.
Read full answer
2/21/2023 4:35:42 AM •Home•Answeredon Feb 21, 2023
0helpful
1answer
Please don't type in all CAPS, it is considered SHOUTING and is harder to read.If it really is 'Todco', and that model, nowhere.https://www.google.com/search?q=todco+gr301-68+parts+listThere are some secondhand ones, but it appears to be a brand with no maker. You could use a Terracotta flower pot base? It is ceramic and glazed inside. They come in many diametershttps://www.google.com/search?q=Terracotta+flower+pot+basehttps://www.google.com/search?q=TODCO+GR301-68..
Read full answer
2/18/2023 10:44:55 PM •Home•Answeredon Feb 18, 2023
0helpful
1answer
It is probably 'Westclox', not 'West Clock' and 70045? They are usually very basic with no adjustment. Some have an Automatic Light Sensor, or it may just be that the capacitor that powers the display is failing.No manualhttps://www.google.com/search?q=Westclox+7045+manual
Read full answer
2/12/2023 11:46:39 PM •Home•Answeredon Feb 12, 2023
0helpful
1answer
no info generic answer --a socket on a pipe --open end wrench --ratchet open end claw wrench --remove parts to access valve unit
Read full answer
2/10/2023 9:13:39 PM •Home•Answeredon Feb 10, 2023
0helpful
1answer
I am not a service professional, but just a homeowner who has some experience with this gas log.GAS LOG INSTRUCTIONSBrand: Marco Gas Log (company is now out of business)#792775, unvented gas logInstalled late 1990's when house was builtThe gas is turned on and off using the key on the wall to the left of the fireplace. The gas is OFF when the key is turned as far clockwise as possible. Turn the key counterclockwise about a half turn or whole turn (180 degrees to 360 degrees) to light the pilot and turn on the log. You don't have to worry about gas coming out into the room before you light the pilot, or if the pilot goes out.Horizontal as far clockwise as possible = OFFVertical ½ turn = ONThe log needs to be cleaned before using at the beginning of the season. Remove the logs, taking note of their position so you can replace them the same way. Use a toothbrush to clean the thermocouple, which looks like two little wires immediately to the right of the pilot (which looks like a metal tube that is located in the center just in front of the back log). Use a vacuum cleaner hose and duster to clean dust off all metal parts and the fire box interior. You can go ahead and replace the back log before lighting the pilot.HOW TO LIGHT THE PILOT:With the gas turned on with the key on the wall, find the black and white knob on the lower right of the gas log and turn it all the way to the right (clockwise) to the to the right as far as it will go, then turn it back ever so slightly to the left until you feel a little resistance (like a click that you feel rather than hear). The pilot cannot be lit when turned all the way to the right.Push the knob in with your thumb and use your other hand to light the pilot with a long-stem lighter or match. Hold the knob in for at least 30 seconds. The thermocouple has to be hot before the pilot will stay on. Let the knob come out very slowly. Hopefully the pilot will remain lit, but if it does not, you will need to repeat the procedure until it does. Be sure to hold the knob in until the thermocouple is hot and release the knob very carefully. When the pilot stays lit, then turn the knob to the left counterclockwise until the flame stays lit and carefully place the logs back into their original position. Note: Push the knob in only when you are actually lighting the pilot, not while you are turning the knob.Set the thermostat from Hi to Low as pictured on the knob. Once the log is lit, it should stay on until the thermostat causes it to go off. Hopefully the pilot will stay on so that the log will come back on automatically according to the setting of the thermostat (from low to high). It will be at its hottest when the knob is all the way counterclockwise.The flame will go off and on according to the temperature in the room. The pilot should stay lit even when the main flame goes out, as shown above.
Read full answer
2/10/2023 8:03:19 PM •Home•Answeredon Feb 10, 2023
0helpful
1answer
Question edited for clarity, and add MAKER, so few words, so many spelling mistakes!Lithium batteries aren't rechargeable. Your small round CR2032 battery lasts 8 years. It is the same battery in a computer motherboard and easy to find in any pharmacy.REPLACING 3V LITHIUM BATTERY The Auto-set time memory is maintained by a lithium button cell battery, model CR2032. The expected life of this battery is about 8 years. Be sure that the 2 "AA" batteries in the clock are fresh. The MODE switch (8) must be in the RUN position when replacing this button cell battery. This battery is located in the small round battery compartment on the rear of the clock secured by a screw. Open the battery compartment (3) with a screw driver and replace the CR2032 lithium battery observing the polarity. Then close the compartment securing with the screw.https://cdn.shopify.com/s/files/1/0035/7443/1790/files/40222s-40222b_1.pdf?v=1594066127..
Read full answer
2/8/2023 3:21:47 AM •Home•Answeredon Feb 08, 2023
0helpful
1answer
not a CAR so moved yah/FEBO Flame Electric Fireplacereal name is this.contract the maker , we are not them,
Read full answer
2/5/2023 1:15:30 AM •Home•Answeredon Feb 05, 2023
0helpful
1answer
This is the striplight for it. It should last years.https://www.amazon.com/Replacement-Clairol-Makeup-Technical-Precision/dp/B08L9S3K2MNothing shows how, but it has to be easy. I would guess accessed from the back.https://www.google.com/search?q=Clairol+true+to+light+V11+how+to+replace+bulbs..
Read full answer
1/28/2023 1:35:50 AM •Home•Answeredon Jan 28, 2023
0helpful
4answers
use this link to see:http://www.medicinenet.com/image-collection/bedbug_bites_picture/picture.htm
Read full answer
1/23/2023 6:05:21 AM •Home•Answeredon Jan 23, 2023
0helpful
2answers
It is possible that the head section of your Invacare bed is not able to raise to a 90-degree angle due to a mechanical issue with the bed. It could be due to a problem with the motor or gears that control the movement of the head section, or it could be due to an issue with the electrical components that power the bed.You should check the following things:
- Check the bed's remote control to ensure that it is functioning properly.
- Make sure that the bed's power cord is securely plugged into the outlet and that the outlet is working properly.
- Check the bed's battery level, if the bed has a battery backup.
- Make sure that the bed is not locked in place or that the manual lock is not engaged.
- Check that all the bed's connections are secure, and all the bed's cables are properly plugged in.
If none of these solutions resolve the issue, it may be necessary to contact the manufacturer or a healthcare equipment repair service for further assistance.
Read full answer
1/23/2023 5:58:29 AM •Home•Answeredon Jan 23, 2023
0helpful
1answer
To pair/sync a second remote switch to an existing Intertek 3177973 receiver, you will need to follow these steps:
- Turn off the power to the existing fan/light unit by switching off the circuit breaker or removing the fuse.
- Locate the "learn" button on the receiver. It is usually located on the back of the receiver or the control box.
- Press and hold the "learn" button on the receiver until the LED light on the receiver starts flashing.
- Press the "on" button on the new remote switch for about 5 seconds. The LED light on the new remote switch should start flashing.
- Release the "on" button on the new remote switch. The LED light on the new remote switch should stop flashing, and the LED light on the receiver should stop flashing.
- Test the new remote switch to make sure it is controlling the fan/light unit properly.
7. Turn on the power to the existing fan/light unit.It's important to note that these steps are general guidelines, and the specific steps may vary depending on the model of your Intertek 3177973 remote control unit. Consult the manual for the specific steps and precautions before pairing or syncing on your remote control unit.
Read full answer
1/14/2023 1:25:14 AM •Home•Answeredon Jan 14, 2023
0helpful
2answers
To calibrate a digital scale, you will need to follow these steps:
- Find a weight that you know the exact weight of, such as a coin or a small weight. This weight will be used to calibrate the scale.
- Place the weight on the scale and wait for the scale to stabilize.
- Check the weight displayed on the scale. If it is not accurate, use the scale's calibration function to adjust the scale to the correct weight.
- To calibrate the scale using the calibration function, follow the instructions in the user manual for your specific scale. The process may vary depending on the make and model of the scale.
- Once the scale is calibrated, remove the weight and test the scale by weighing an object of known weight. If the scale displays the correct weight, the scale is properly calibrated. If the scale is still not accurate, you may need to repeat the calibration process or consult the user manual for further instructions.
I hope this helps! If you have any further questions, don't hesitate to ask.
Read full answer
1/8/2023 11:03:22 PM •Home•Answeredon Jan 08, 2023
0helpful
1answer
It appears to be Australian and we are in North America. This link may work better for you. If you have another computer, perhaps at work it will play DVDs.https://www.google.com/search?q=Nutrimax+oil+core+skillet..
Read full answer
1/8/2023 5:57:49 AM •Home•Answeredon Jan 08, 2023
0helpful
1answer
To remove the comma from the price, you can use a string manipulation function such as replace(). Here's an example of how you can use it in Python:Copy codeprice = "21.36" price = price.replace(",", "") print(price) # Output: "2136" This will replace all occurrences of the comma character with an empty string, effectively removing the commas from the price.You can also use this function to remove the decimal point, if desired. For example:Copy codeprice = price.replace(".", "") print(price) # Output: "2136"
Read full answer
1/6/2023 12:07:34 PM •Home•Answeredon Jan 06, 2023
0helpful
2answers
have seen some nursery rhymes musical figurines http://www.themusicboxcompany.com/baby_children.htm#nurseryrhymes scroll down to nursery rhymes
Read full answer
1/6/2023 5:51:58 AM •Home•Answeredon Jan 06, 2023
0helpful
2answers
have you checked/replaced batteries. Be sure to install correctly. You can call Tempurpedic or the store sold it to you for more help.
Read full answer
12/29/2022 12:27:31 AM •Home•Answeredon Dec 29, 2022
- Prev
- 1
- ...
- 6
- 7
- 8
- 9
- 10
- 11
- Next